Hardware for Clocks

Showing 1–16 of 62 results

  • launch

    View Product

    View more

    turned_in_out Hardware for Clocks

    Mechanical Clock Suspension Spring

    This is the most common suspension spring needed by far. Suspension A1 is for mantle clocks, A2 for wall and grandmother units. The suspension A3 is for larger floor clocks such as a grandfather clock.

    SUS-A: $10.00$25.00
    View Product
  • launch

    View Product

    View more

    turned_in_out Clock Weight Accessories

    Clock Weight Top Hook

    Brass top weight hook for modern German clock movements such as Hermle / Urgos / Kieninger. Comes either with external threads or internal threads. The M* number is the thread size of the screw/bolt, M4 is 4mm, M5 is 5mm.

    WE6: $6.00
    View Product
  • launch

    View Product

    View more

    turned_in_out Hardware for Clocks

    German Clock Hand Nuts

    German clock hand nuts for post 1950 clock movements. Fits Hermle, Kieninger, Urgos, Jauch and more. However these hand nuts will not work on a cuckoo clock. Cuckoo clock hand nuts are available on the cuckoo parts page.

    CP9: $10.00
  • launch

    View Product

    View more

    turned_in_out Hardware for Clocks

    Round Convex Clock Glass

    Round convex clock glass gets measured from one side to the other, the overall width. When working with a clock bezel it is important to order the right sized clock glass. If the glass is too narrow it will fall out the front of the bezel.

    BZ2: $8.00$70.00
    View Product
  • launch

    View Product

    View more

    turned_in_out Hardware for Clocks

    Pendulum Suspension Spring Rods

    Frequently needed pendulum suspension spring rods in 17 inch lengths. These suspension rods are cut, bent, and modified as needed for the pendulum to hang onto the clock. They replace the pendulum suspension rods that have worn out and has the spring steel broken.

    LSUS-C: $10.00
  • launch

    View Product

    View more

    turned_in_out Hardware for Clocks

    Clock Dial Key Grommets

    Three winding hole key grommets to be used on a clock dial with a 3/8 wide hole. They are to be installed on the dial after drilling out the winding arbor holes.

    CP32: $5.00
  • launch

    View Product

    View more

    turned_in_out Hardware for Clocks

    Clock Parts Chime Hammer

    The chime hammers are the clock parts that strike the chime rods. Three sizes to choose from and this is the approximate length of the hammer head with the tip and screw. The tips of the hammers come in two ways.

    CP1: $1.00$10.00
    View Product
  • launch

    View Product

    View more

    turned_in_out Clock Weight Accessories

    Clock Chain End Hooks

    Hook and ring set for chain driven floor clock models. The chain link only consists of a bent wire that loops around to itself. Only needs two needle nose pliers to open the connecting point on the link and install these pieces.

    CP16: $5.00
  • launch

    View Product

    View more

    turned_in_out Cuckoo Clock Parts

    Cuckoo Chain Hook Set

    Installation of the cuckoo chain hook and ring set is easy. Each link on the chain is only a wire folded into a unsoldered loop only. With two needle nose pliers a simple twist is all that is is needed to open the link.

    CU15: $5.00
  • launch

    View Product

    View more

    turned_in_out Hardware for Clocks

    Clock Hand Washer Assortment

    100 Assorted mixed clock hand washers used on antique wall and mantle clocks. These go on top the minute hand on some clocks to maintain tension so the hand does not move around.

    CP7: $10.00
  • launch

    View Product

    View more

    turned_in_out Cuckoo Clock Parts

    Cuckoo Clock Hand Nuts

    6 nuts and 6 washers to fit the hand shaft of a post 1950 cuckoo clock. This nut is screwed onto the end of the hand shaft to keep the minute hand in place.

    CU20: $15.00
  • launch

    View Product

    View more

    turned_in_out Hardware for Clocks

    Grandfather Grandmother Clock Chain

    Grandfather grandmother clock chain by movement maker or links per foot LPF. Count the links on the old chain so it matches the LPF on the drop down menu.

    Chain: $6.00$25.00
    View Product
  • launch

    View Product

    View more

    turned_in_out Hardware for Clocks

    Clock Repair Tapered Pins

    Used in clock repair these tapered pins come in an assortment of 100 sizes and diameters. These Clock Parts have many uses in clock repair. They attach some dials, movement plates, suspensions and sometimes hands on the clock.

    CP2: $15.00
  • launch

    View Product

    View more

    turned_in_out Hardware for Clocks

    American Clock Hand Nuts

    American clock hand nuts mixed steel and brass. This is a 12 pack of hand nuts that are all the same thread size. They are likely to fit American time strike units produced from around 1930 to 1950's.

    CP14: $10.00
  • launch

    View Product

    View more

    turned_in_out Clock Weight Accessories

    Polished Clock Weight Cap

    Polished brass tone weight shell end caps are the tops and bottom of the weight shell. Available in 43mm, 47mm or 60mm diameters and sold individually.

    WE1: $6.00
    View Product
  • launch

    View Product

    View more

    turned_in_out Hardware for Clocks

    Sticky Arabic Clock Numerals

    Peel and stick Arabic style clock numerals for making clocks or replacing lost numbers. Complete set of 12 numerals in gold tone color and made of durable plastic.

    DL18: $5.00
    View Product