400 Day Clock Parts

400 Day Anniversary Clock Parts

The suspension spring on your clock needs to be replaced if its kinked or distorted. Read More »

The suspension spring is the part on the back of the clock that supports the pendulum balls in the air. This is almost always the fist issue to deal with to get the clock running. This happens when someone is not familiar with the clock and they move it from here to there with the pendulum getting knocked around and the spring gets twisted and kinked.

Anniversary Clock Repair Kit

Showing 1–16 of 23 results

  • Brass Single-End Clock Key Brass Single-End Clock Key
    Brass Single-End Clock Key Single end brass clock key to wind up a wall or mantle mechanical clock movement. See instructions on the top tabs for how to get the right size key for your clock. Almost all post 1 ...
    CK4: $9.89
    View Product
  • 400 Day Anniversary Clock Suspension Springs 400 Day Anniversary Clock Suspension Springs
    Anniversary Suspensions Single Strengths in a three pack, springs only Available in all inch sizes between .0018 and .0040 Specify size with the drop down list below. To determine the size, measure the existing spring ...
    AN1: $9.89 – $19.89
    View Product
  • Blocks and Forks Blocks and Forks
    Blocks and Forks Choose between top block, fork or bottom block Be sure not to bend the suspension spring when installing any of this hardware Suspension springs bend very easily and the clock cannot run if ...
    AN2: $4.89
    View Product
  • Hand Remover Puller Hand Remover Puller
    Removes stubborn hands and gears in a straight motion. Sometimes this would be needed to remove the wheel on the back that lifts the bellow lift wires also. ...
    CU30: $9.89
  • Vision Visor Magnification Head Band Vision Visor Magnification Head Band
    This magnifier can be worn over glasses. This fits over the head and will be the most convenient magnification for inspecting important components of the clock movement and parts. This quality tool is made here in USA. D ...
    CT17: $24.89
  • Clock Oil With Oiler Clock Oil With Oiler
    Clock Oil With Oiler Precision pen oiler that is filled with quality general purpose clock oil. The applicator makes it easy to oil hard to reach pivot holes. Oiling a clock is done with the oiler to put the smallest dr ...
    CT3: $9.89
  • Clock Mainspring Let Down Tool Set of 2 Clock Mainspring Let Down Tool Set of 2
    Used to release the power in a wound up mainspring. Key goes into the chuck and the chuck goes into the handle so you can let down the power of the spring. It does the same job as the let down with all the chucks. If som ...
    CT26: $29.89
  • Anniversary Clock Glass Dome Anniversary Clock Glass Dome
    Replacement solid glass clock dome for anniversary or 400 day style clocks ...
    AN5: $14.89 – $69.89
    View Product
  • 400 Day Anniversary Clock Repair Guide 400 Day Anniversary Clock Repair Guide
    10th edition Hardcover Identifications, Repair tips, and Troubleshooting. It also includes an extensive collection of back plate and suspension illustrations which aid clock identification and the selection of replaceme ...
    CB6: $39.89
  • Schatz Lantern Clock Key Schatz Lantern Clock Key
    Schatz Key Long brass key #3 size Fits most Schatz Lantern style 400 day clocks. If the clock is not made by Schatz, then see the other keys below or go to the clock key page. This key is longer than the norm to ...
    AN3: $14.89
  • Assorted Files Assorted Files
    Set of 12 needle files for various uses in clock repair. There are many assorted shapes. ...
    AN14: $14.89
  • Hand Remover Tool Hand Remover Tool
    Removes hands and gears in a straight upward motion to prevent damage. It is not uncommon to have a hard time taking off the hour hand on these anniversary clocks. ...
    AN8: $9.89
  • 6PC Screw Driver Set With Rotatable Tops 6PC Screw Driver Set With Rotatable Tops
    Six precision screwdrivers, four sizes of the flat head and two phillips style. The blades have a rust resistant black oxide finish, and they are made of durable chrome molybdenum steel. The top rotates for ease of use a ...
    CT14: $14.89
  • Pin Vise Set Pin Vise Set
    Set of 4 with capacities from .0mm to 4.65mm. Good to use on broaches when reaming out a pivot hole diameter. Grabs hold of a post of some sort so you can work with it basically. Small part of the pinvise is knurled so i ...
    AN18: $14.89
  • 400 Day Repair Guide 400 Day Repair Guide
    10th edition Hardcover 9x10 with 237pgs Identifications, Repair tips, and Troubleshooting. It also includes an extensive collection of back plate and suspension illustrations ...
    AN4: $39.95
  • Digital Caliper Four Inch Digital Caliper Four Inch
    This 4inch digital calipers stainless steel construction allows you to get metric or SAE decimal readings even in harsh conditions. The easy-to-read digital display allows you to measure and convert from SAE to metric qu ...
    CT43: $29.89