Hermle

launch

question_answer 3 Questions/Answers

View more

turned_in_notHermle

When the clock misses the stopping point sometimes and chimes more than one quarter at a time, or just chimes forever, this is the correction. There is a cam with graduated humps on the top right of the front plate of the Movement. There are 4 lower portions with a small hump and the next one is bigger and then… View Product

launch

question_answer 0 Questions/Answers

View more

turned_in_notHermle

Grandfather Clock Moon Gear Installation is as follows. The moon phase function is only run by one gear. The gear is called a Moon Gear and sits behind the dial, on the same tube as the hour hand. It is easy to remove by loosening the one set screw and it will slide off. It gets put on the new… View Product

launch

question_answer 0 Questions/Answers

View more

turned_in_notHermle

On rare occasions 451/1151 high bridge units have the suspension post longer on the new movement than the old one, although both units may be High Bridge. This may cause issues with the pendulum interfering with the chime block. This is usually no issue at all and the clock will function like it ever did. Just bend the hammers on… View Product

launch

question_answer 0 Questions/Answers

View more

turned_in_notHermle

  Hermle mechanical clock movements are among the finest movements made in the modern times. The German made Hermle mechanical clock movements units typically work night and day for 30 years without much complaint. To get an overhaul, like you normally would with any clock, is found to be a much higher cost. This is for good reason as it… View Product

launch

question_answer 0 Questions/Answers

View more

turned_in_notHermle

A clock bezel description consists of the brass part that holds the clock glass in place. It can be confusing to get the bezel and then the flat or convex glass. To buy the clock bezel and then try to get the correct glass separately to put them all together is not easy. It is best to get the clock… View Product

launch

question_answer 0 Questions/Answers

View more

turned_in_notHermle

The intent of this post is to explain the Hermle Clock Code Letters that follow the movement number on Hermle movement. Sometimes customers think that if the new movement does not have the same letter as the old unit that it will not be the same. This is not always the case. This is what follows a typical Hermle number… View Product

launch

question_answer 0 Questions/Answers

View more

turned_in_notHermle

Of course Clockworks offers excellent availability on all Hermle mechanical clock movements. In fact, all Hermle clock movements are in stock with very few exceptions. However, a certain pendulum CM length that was available in the past may not be available off the shelf. Thus, this situation would require a regear with a new movement. Specifically, this means that a… View Product

launch

question_answer 0 Questions/Answers

View more

turned_in_notHermle

Mechanical clock pendulum top hooks replace broken top hooks or to build a new pendulum. This is a nice alternative to replacing an entire clock pendulum if the top is broken or missing. The top hook is the very top of the pendulum that will enable the pendulum to hang on the leader. To clarify, the leader is the 4… View Product

launch

question_answer 1 Questions/Answers

View more

turned_in_notHermle

The Mechanical Clock hands in the list below are sold by dial diameter size. Alternately, this is not the same method as a clock that operates on a battery. Instead, determine the hands for mechanical clocks as an after effect of measuring the dial diameter. Furthermore, a time track is the outer ring that clocks sometimes have just outside the… View Product

launch

question_answer 0 Questions/Answers

View more

turned_in_notHermle

The installation of the clock hands on a German mechanical movement is reverse of removal. If either the movement was replaced, or the hands are new, the minute hand must be adjusted. This is so it will point to the correct time when it chimes. First comes the hour hand as a friction fit. Put the hand on its round… View Product

launch

question_answer 0 Questions/Answers

View more

turned_in_notHermle

Symptoms would be a clock that runs too fast. The clock pendulum does not have a wide swing to it. The clock has the right pendulum length but it is too fast for adjustment on the rating nut threads. The new style 1161-series does not have an adjustable anchor height adjustment on the movement. However it does still need to… View Product

launch

question_answer 0 Questions/Answers

View more

turned_in_notHermle

Hermle Clock Movement – Replace instead of repair. A fraction of the price, lasts longer, ships now. Instructions and expert support. – Clockworks To get a replacement 261 Hermle Clock Movement all you need are the numbers off of the back plate. If the numbers match then the 261 Hermle Clock Movement matches. Assistance = 800-381-7458 If the clock is a pendulum unit,… View Product