Clock Movement Hole-End Mainsprings

MainspringsMeasuring the MainspringAssessment of damageReplacement serviceRemoving a barrelHermle barrel numbers

Please view these information tabs to help with the proper Clock Movement Hole-End Mainsprings size for your clock.

How to measure Hole End Mainsprings

In order to accurately measure your hole end mainspring it needs to be removed from the barrel. When a spring is contained within a brass barrel, it is always going to be a hole end mainspring.

To begin with, when the spring is removed from the barrel it needs to be stretched out. The length, width and thickness has to be determined in order to select the correct spring. The new spring needs to match up as close as possible with the old spring.

First, measure the width of the spring so it can be matched up in the chart. Second, use a micrometer to determine the thickness. Finally, carefully extend the spring to get the approximate length.

Now that you have your dimensions, match the width first. Then find the closest thickness followed by the length. Remember, you are searching for dimensions that are closest to your old spring. They may not match up exactly, so do your best to get one that is the closest match. The diameter column is the measurement of the inside of the brass barrel.

WARNING: Always wear safety glasses and gloves when working with hole end mainsprings! They can, and are undeniably dangerous. If you choose, we have a mainspring replacement service. All you have to do is send us the entire barrel and we will do all of this work for you.

When we get the barrel, we will use special tools to safely remove the spring and measure it. All of the dimensions described above will be carefully matched up and the new spring will be professionally installed. Your new spring is then shipped back to you in whatever method you chose when checking out.

If you decide to utilize our services, please leave the mainspring inside the barrel. Do not remove the spring yourself. We have a few reasons for this. First, we need to know which way the clock mainspring gets wound inside the barrel. We in turn then know how to replicate this with the new one. Secondly, mainsprings are dangerous and we do not want anyone to get hurt.

Measuring a Hole End Mainspring

- - The content of this web page and web site was written and copyright by James Stoudenmire of Clockworks.com - It may not be used commercially without permission. - -

Clock Mainspring Damage

When a hole end mainspring breaks in the barrel, the impact can cause damage to the clock mainspring. This would be evident in parts of the gear train. It is possible that the pivots were bent or the arbors were bent. Before ordering a mainspring, the condition of the clock movement should be checked.

What to check

One place to check for damage are the teeth on the mainspring barrel. A barrel is what contains the mainspring. The next wheel up on the gear train is the next place to check. This area gets the most impact and is where most of the damage would be. Closely inspect the teeth on the gears to see if they are bent or broken. We also recommend checking the arbor on that wheel. An arbor is another area that often gets bent when the mainspring breaks.

If the movement is damaged beyond reason, it is best to just get a new movement, if it is still in production. In the event that the movement is not in production, you can send it to us for an overhaul here at clockworks.com. We will repair these items as well as clean, oil, re-bush and test the unit. Clockworks also offers a mainspring repair service if you would rather have us replace the spring.

Get a new movement instead

Any movement that is 25-30 years old, has lived its life. A new movement would be the best thing at this point because of the cost and time it would take to make it right. To discuss purchasing a new movement instead of replacing the mainspring, please email us at [email protected] When emailing us, make sure to include the movement number off of the back plate of the movement itself. This is how movements are identified and then we will know what you are working with.

- - The content of this web page and web site was written and copyright by James Stoudenmire of Clockworks.com - It may not be used commercially without permission. - -

Hole End Clock Mainspring replacement service

Because the spring is encased in a barrel, it is easily able to be sent in for repair. Upon receipt of the clock barrel, we will replace the hole end clock mainspring within that barrel. The price for this service is $75 and includes the cost of the mainspring. Upon checkout, you will be prompted to pay for shipping. This shipping charge is your prepayment for the barrel to be shipped back to you.

What will be done

Upon receipt of the barrel, the broken, or worn, spring is removed from the container in a safe manner. Once the spring is out, it is stretched and measured for the thickness, width and length. Next we use the mainspring chart to match up all of the measurements in order to select the correct spring. Clockworks carries a vast array of springs on hand at all times so we can complete your repair in a timely fashion. The final installation of the spring will be done with a special tool called a mainspring winder.

Shipping a Hole End Clock Mainspring replacement For Service

Please mail the barrel with the broken mainspring to Clockworks, PO Box 339, Huntington MA 01050. Be sure to include a copy of your receipt for the Hole End Clock Mainspring replacement service. Additionally, payment for this service can be completed at this link.

- - The content of this web page and web site was written and copyright by James Stoudenmire of Clockworks.com - It may not be used commercially without permission. - -

Removing a clock mainspring barrel

Often a clock mainspring barrel can be removed without disassembling the clock movements outer plates. The mainspring will also still be contained within the barrel.

Letting down the mainspring power

First you would use a mainspring let down tool. This device allows you to hold the tension of the mainspring with your fist rather than your fingers. Put the mainspring let down tool over the square post the key goes onto. With a flat screwdriver, move the "click" out of the way. The click has a tension spring that needs to be held back. This is what holds the mainspring so that it winds in only one direction. Slowly allow the mainspring to unwind in your fist. This method lets you control the speed of the unwind with your whole fist rather than your fingers. Unquestionably, doing this with a key will result in a painful experience on the fingers. Of course, if the mainspring is broken, there usually is no worry since there isn't much tension to begin with.

After the barrel is out

Once the power has been let down, the next step is to yank out the winding arbor shaft. The clock mainspring barrel should then fall out the side of the movement. After the barrel is removed, you will be able to see the number that is on the barrel end cap. This will allow you to determine what hole end mainspring to order. You can locate the mainspring by using the hole end mainspring chart. Be sure to check the movement for any damage as a result of the mainspring breaking. In particular, inspect the teeth of the gears, as well as the arbor on the next wheel up. This could have consequently been bent.

- - The content of this web page and web site was written and copyright by James Stoudenmire of Clockworks.com - It may not be used commercially without permission. - -

Hermle mainspring barrel numbers

Hermle mainspring barrel numbers

Hermle mainspring barrels have numbers on the barrel caps and therefore can be used to help identify the spring contained therein. Generally speaking, these numbers sometimes can only be seen by removing the barrel from the clock because of where the number is placed on the cap, but there will certainly be a number on it. The chart provided on this page lists the various numbers found on the caps, as well as the corresponding mainspring that will ultimately be found inside that barrel.

Hermle mainspring barrel number to size spring
Barrel Number Mainspring Dimensions MM
10 17 x .45 x 1490
11 17 x .42 x 1500
20 & 56 17 x .38 x 1200
21 & 50 17 x .40 x 1200
31 12 x .34 x 1150
32 12 x .42 x 1100
33 12 x .32 x 1150
40 17 x .38 x 1100
41 21 x .40 x 1550
42 17 x .40 x 1100
52 17 x .42 x 1200
54 21 x .42 x 1900
55 21 x .45 x 1800

Check for damage

Once you have obtained the size of the spring needed by the Hermle mainspring barrel number, you can therefore go ahead and find it on the hole end mainspring chart so you will be able to order a new one. Of course, if it needs a mainspring, it is quite probable that the teeth of the barrel may have been damaged when the spring broke. This is because of the incredible power of the spring. Consequently, another area that may have also gotten damaged are the teeth on the next wheel up on the train. As a result of these problems, it would be best to purchase a new movement.

Get a new movement instead

In order to identify the movement, you would first need to locate the movement number. Therefore, the back plate of the movement itself needs to be looked at. The number will be stamped right into that brass plate. Although customers sometimes think they can get the number off of the clock case, or the paperwork that came with the clock, this is not the case. The only place that number will be is stamped into the brass. As soon as you have the numbers from the movement you can go to this page to finally find your brand new clock movement.

Another problem that occurs when the mainspring breaks is the second wheel up from the barrel gets a bent arbor. This is certainly something that needs to be checked. If the arbor did get bent, you would surely need to get a new wheel, or somehow straighten it out. Indeed, it is not always easy to get it straight, so again, sometimes it is best to just get the new unit instead.

- - The content of this web page and web site was written and copyright by James Stoudenmire of Clockworks.com - It may not be used commercially without permission. - -

Instructions

The width is measured first and matched up to the width below, then the thickness is measured with a micrometer, then the approximate length.

Choose the item number of that mainspring from the order list of options and push the add to cart button.

Clear
HEMSP: $9.89$39.89

Hole End Mainsprings Measurements to item #
WIDTH inch | mm THICKNESS inch | mm LENGTH inch DIAMETER mm Item #
3/32" | 2.3 .007" | 0.18 18" 14 CMH 100
5/32" 4 .008" | 0.2 24" 17 CMH 101
5/32" 4 .011" | 0.28 26 1/2" 22 CMH 103
3/16" 4.8 .009" | 0.23 24" 17 CMH 104
7/32" 5.6 .008" | 0.2 26" 20 CMH 105
7/32" 5.6 .0095" 0.24 24" 18 CMH 106
1/4" 6.4 .011" 0.28 15 3/4" MB CMH 109
1/4" 6.4 .011" 0.28 39" 26 CMH 110
9/32 7 .007" 0.18 44" 19 CMH 111
9/32 7 .010" 0.25 18" MB CMH 112
9/32" 7 .010" 0.25 39 1/2" 25 CMH 113
5/16" 8 .008" 0.2 27" 18 CMH 114
5/16" 8 .010" | 0.25 28" 19 CMH 116
5/16" 8 .010" | 0.25 32" 23 CMH 117
5/16" 8 .010" | 0.25 39 1/2" 25 CMH 118
5/16" 8 .011" | 0.28 45 1/4" 28 CMH 119
5/16" 8 .015" 0.38 40" 34 CMH 120
5/16" 8 .016" 0.41 54" 38 CMH 121
11/32" 8.7 .013" 0.33 66" 38 CMH 122
23/64" 9 .011" 0.28 45 1/4" 28 CMH 124
23/64 9 .0125" 0.32 18 1/2" MB CMH 125
3/8 9.5 .011" 0.28 48" 26 CMH 126
3/8" 9.5 .014" 0.36 48" 32 CMH 127
3/8" 9.5 .017" 0.43 54" 38 CMH 128
25/64" 10 .011" 0.28 45 1/4" 28 CMH 130
25/64" 10 .012" | 0.32 73" 40 CMH 131
7/16" 11 .010" | 0.25 32 1/4" 22 CMH 132
7/12" 11 .011" | 0.28 49" 28 CMH 135
7/16" 11 .0155" | 0.4 55 1/2" 38 CMH 136
15/32" 12 .010" | 0.25 39 1/2" 25 CMH 137
15/32" 12 .012" 0.3 53" 32 CMH 139
15/32" 12 .014" 0.36 72" 41 CMH 140
15/32" 12 .013" 0.33 27" 25 CMH 141
1/2" 12.7 .013" 33 60" 36 CMH 142
1/2 12.7 .015" 0.38 36" 25 CMH 143
1/2 12.7 .016" 0.41 65" 32 CMH 144
1/2" 12.7 .018" 0.46 60" 38 CMH 145
33/64" 13 .010" 0.25 39 1/2" 25 CMH 146
33/64" 13 .010" 0.28 45 1/2" 28 CMH 147
33/64" .012" | 0.3 53" 32 CMH 148
33/64" 13 .014" | 0.36 38" 30H CMH 150
33/64" 13 .022" | 0.55 28" 32H CMH 151
17/32" 13.5 .010" | 0.26 72" 34 CMH 149
35/64" 14 .011" | 0.28 45 1/4" 28 CMH 152
35/64" 14 .011" 0.28 49" 30 CMH 153
35/64" 14 .012" 0.3 61" 35 CMH 155
35/64" 14 .0155" 0.4 37 1/2" 36 CMH 156
9/16" 14.3 .012" 0.3 39" 28 CMH 157
35/64 14 .013" 0.33 27" 25 CMH 158
35/64 14 .014" 0.36 32" 30 CMH 159
9/16" 14.3 .015" 0.38 42" 28 CMH 160
19/32" 15 .011" 0.28 45 1/4" 28 CMH 161
19/32" 15 .011" | 0.28 49" 30 CMH 162
19/32" 15 .012" | 0.3 53" 32 CMH 163
5/8" 16 .010" | 0.25 39 1/2" 25 CMH 164
5/8" 16 .011" | 0.28 45 1/4" 28 CMH 165
5/8" 16 .011" | 0.28 49" 30 CMH 166
5/8" 16 .013" 0.33 78" 34 CMH 167
5/8" 16 .013" 0.33 105" 47 CMH 168
5/8" 16 .014" 0.36 70" 39 CMH 169
5/8" 16 .016" 0.41 59" 35 CMH 170
5/8 16 .0175" 0.45 43 1/2" 37 CMH 171
5/8 16 .018" 0.46 41" 36 CMH 172
5/8" 16 .018" 0.46 72" 40 CMH 173
5/8" 16 .018" 0.46 96" 53 CMH 174
43/64" 17 .010" | 0.25 72" 34 CMH 176
43/64" 17 .010" | 0.25 39 1/2" 25 CMH 177
43/64" 17 .011" | 0.28 45 1/4" 28 CMH 178
43/64" 17 .011" | 0.28 49" 30 CMH 179
43/64" 17 .018" | 0.46 54" 40 CMH 180
11/16" 17.5 .012" 0.3 72" 30 CMH 181
11/16" 17.5 .014" 0.36 54" 34 CMH 182
45/64" 18 .018" | 0.46 44" 38 CMH 183
11/16" 17.5 .018" 0.46 96" 53 CMH 184
45/64" 18 .011" 0.28 45 1/4" 28 CMH 185
45/64 18 .011" 0.28 49" 30 CMH 186
45/64 18 .012" 0.3 53" 32 CMH 187
45/64" 18 .012" 0.3 61" 35 CMH 188
45/64" 18 .016" 0.41 56" 39 CMH 189
45/64" 18 .016" 0.41 61 1/2" 42 CMH 190
45/64" 18 .0175" | 0.44 70" 45 CMH 191
45/64" 18 .019" | 0.48 47" 35 CMH 192
45/64" 18 .021" | 0.53 48" 40 CMH 193
3/4" 19 .009" | 0.23 72" 33 CMH 194
3/4" 19 .010" 0.25 39 1/2" 25 CMH 195
3/4" 19 .011" 0.28 45 1/4" 28 CMH 196
3/4" 19 .011" 0.28 49" 30 CMH 197
3/4" 19 .011" 0.28 50" 30 CMH 198
3/4 19 .012" 0.3 53" 32 CMH 199
3/4 19 .012" 0.3 61" 35 CMH 200
3/4" 19 .012" 0.3 75" 35 CMH 201
3/4" .012" 0.3 90" 35 CMH 202
3/4" 19 .014" | 0.36 90" 35 CMH 204
3/4" 19 .015" | 0.38 72" 36 CMH 205
3/4" 19 .0155" | 0.4 53 1/2" 37 CMH 206
3/4" 19 .016" 0.41 53" 38 CMH 208
3/4" 19 .016" 0.41 56" 39 CMH 209
3/4" 19 .016" 0.41 60" 38 CMH 210
3/4" 19 .017" 0.43 44" 35 CMH 211
3/4 19 .017" 0.43 45" 36 CMH 212
3/4 19 .0175" 0.44 70" 45 CMH 213
3/4" 19 .018" 0.46 96" 53 CMH 214
3/4" 19 .019" 0.48 68 1/2" 45 CMH 215
25/32" 20 .011" | 0.28 49" 30 CMH 217
25/32" 20 .012" | 0.3 53" 32 CMH 218
25/32" 20 .012" | 0.3 61" 35 CMH 219
25/32" 20 .0155" | 0.4 53" 38 CMH 220
25/32" 20 .016" | 0.41 53" 38 CMH 221
25/32" 20 .0175" 0.44 70" 45 CMH 222
25/32" 20 .018" 0.46 76 1/2" 48 CMH 223
53/64" 21 .011" 0.28 45 1/4" 28 CMH 224
53/64" 21 .011" 0.28 49" 30 CMH 225
53/64 21 .012" 0.3 53" 32 CMH 226
53/64 21 .012" 0.3 61" 35 CMH 227
53/64" 21 .0125" 0.32 67" 38 CMH 228
53/64" 21 .015" 0.38 100" 50 CMH 229
7/8" 22.2 .011" 0.28 49" 30 CMH 230
7/8" 22.2 .012" | 0.3 53" 32 CMH 231
7/8" 22.2 .012" | 0.3 61" 35 CMH 232
7/8" 22.2 .0125" | 0.32 67" 38 CMH 233
7/8" 22.2 .013" | 0.33 72" 33 CMH 234
7/8" 22.2 .0155" | 0.4 50" 37 CMH 235
7/8" 22.2 .0175" 0.44 70" 45 CMH 236
7/8" 22.2 .018" 0.46 84" 49 CMH 237
7/8" 22.2 .018" 0.46 96" 53 CMH 228
7/8" 22.2 .0195" 0.5 56" 42 CMH 239
61/64 24 .0175" 0.44 70" 45 CMH 240
61/64 24 .018" 0.46 76 1/2" 48 CMH 241
61/64" 24 .018" 0.46 80 1/2" 50 CMH 242
63/64" 25 .018" 0.46 78 1/2" 49 CMH 243
1" 25.4 .018" 0.46 96" 53 CMH 244