Hermle Quartz Clock Movements

Hermle QuartzWhat to do to fix the clockHow to do itHermle quartz removalMeasuring the handshaft lengthBest alternate units

Please view these information tabs to help with determining the proper Hermle Quartz Clock Movements for your clock.

Hermle quartz discontinued what to do for a new unit

Hermle quartz discontinued what to do for a new unit. The Hermle Quartz clock movements are obsolete and no longer available. This means if your quartz clock movement says 2214 or 2215 and has a pendulum, or if it says 2114 or 2115 non pendulum, its no longer made.

We have these alternate movements that have the equivalent sound quality and lasts longer than the Hermle units. There are more features and do not seem to break or have issues during daylight savings adjustments like the Hermle Quartz units did after years of service. To get the new movement, three things are required. First is to be sure the new one will fit into the clock case, as some are bigger in size. Then convert the hand shaft from the old one to the new because it is measured in a different way. Lastly get new hands as your old ones will not fit.

This may sound like alot, but its not that bad really. Once you get the movement out of the clock and measure the hand shaft, you can determine what movement post length to get on the new alternate unit. A hand shaft is the shaft in which the hands go onto and this is measured from the black plastic base and all the way out to the end of the nut threads that go on the minute hand too keep it secure. With this length you can subtract a 1/4 inch and this is the post length needed on the new unit.

- - The content of this web page and web site was written and copyright by James Stoudenmire of Clockworks.com - It may not be used commercially without permission. - -

Replacing Hermle quartz movements

Replacing Hermle Quartz movements is sort of tricky, the units are no longer made and the new ones that are available mount in a different method. The Hermle Quartz clock movements were mounted in a way that is not typical to the rest of the quartz clock movements on the market. This has to be taken into consideration during the quartz clock movement conversion to one of these fine alternate units.

Basically the Hermle Quartz clock movements had a nut that went through the dial side, and into the front of the movement to mount it to the back of the dial. The new unit instead has a post sticking out of the movement that goes through the back of the dial and a hex nut goes on the front dial side to keep the movement mounted to it.

To get the new movement for your clock it would be required to remove the movement from the clock case and do some measuring. So the first step is to get the movement out of the clock. The second is to measure the post that the hands go on, this is measured from the black plastic base and all the way out to the end of the minute hand nut threads. With this measurement you can deduct 1/4 inch from this, and this is the length of the threaded post that is needed on the new alternate substitute clock movement to go into the clock case.

Also note that the hands on the Hermle Quartz units will not fit on the new unit either. They had special hands and the minute hand on the new unit will have a larger hole to mount it with. If you really like the clock hands you have now and do not want to change them, it is possible to take a needle file to the minute hand hole to get it to fit the new unit.

- - The content of this web page and web site was written and copyright by James Stoudenmire of Clockworks.com - It may not be used commercially without permission. - -

Removing Hermle Quartz Movement

Removing Hermle Quartz movement can be tricky as there is not a typical 6 sided nut to take the unit out of the clock like most situations. Instead they used a nut that is slotted on either side of the hand shaft itself to secure the Hermle Quartz movement to the back of the clock dial.

Sometimes removing the clock movement is done a different way. If the movement is mounted to the dial by double sided sticky tape it is needed to pry the movement off the back of the dial and hopefully leaving the dial in tact while doing it.

  1. Remove the second hand. Pull it straight and it will come off.
  2. Take off the minute hand nut, just turn the nut to the left when holding the hand still.
  3. Take off the hour hand, its friction fit only, twist and pull toward you.
  4. There is a nut holding the movement. Its tricky as it has two slots on either side of it. Sometimes its on tight. What we do here is just use two big flat screw drivers, put one on each side of the hand shaft in the nut and turn both together as the same time to the left. Careful not to scratch the dial, this is easy to slip and do.
  5. The movement will fall out of the back.

Now that you are done successfully Removing Hermle Quartz Movement from the clock case, you are ready to determine the best alternate substitute movement for a working clock

- - The content of this web page and web site was written and copyright by James Stoudenmire of Clockworks.com - It may not be used commercially without permission. - -

How to measure the Hermle quartz handshaft

How to measure the Hermle Quartz handshaft is done by the entire hand shaft post that sticks out of the movement, from the plastic and all they way out. We measure this different as we go by just the threaded post that goes through the dial and mounts with the hex nut only.

Hermle used three hand shaft lengths on there base units, these lengths are 16mm, 21mm, and 26mm. There was a time some of the 26mm were modified internally to create a extremely long hand shaft, something like 1 1/4 or 1 1/2 inches, if you have one like this there is no luck for replacement.

The following is a guide line for the old Hermle Quartz hand shaft length, to the length of the threaded post to order from us. It makes it simplistic to just do the following 1. measure the hand shaft on your current Hermle quartz clock movement, 2. Convert to the post length needed with the below information, 3. order whatever movement you would like from us with that post length.

  • 16mm (About 5/8") = Get a 5/16 post
  • 21mm (About 3/4") = Get a 7/16 post
  • 26mm (About 1") = Get a 11/16 post

Hermle Quartz Clock Movement 2214 2215

Next step to replace the Hermle quartz

Now that your old unit is out of the way and you have converted the old hand shaft length to the new post length, we are ready to shop for a replacement. The next step is to take note of the overall size of the new movement and be sure that it will fit in behind the dial ok.

The new unit maybe taller or wider and we just want to be sure it will fit in there. If verified its ok, we can pick a new unit with the post length that was converted. Be sure to get new hands when your done, they are on the same page as the product. This is your old ones will not fit without modifications.

- - The content of this web page and web site was written and copyright by James Stoudenmire of Clockworks.com - It may not be used commercially without permission. - -

Hermle quartz clock movement replacement options

The best Hermle quartz clock movement replacements are listed in priority below. What this means is the closest to the old size, with the best sound quality is rated best on top of the list. Its also priced in this order also, highest to lowest.

  1. MSO Quartz
  2. QU40 Quad Unit
  3. QU30 Seiko Quartz
  4. QU22 Takane Quartz

Hermle quartz clock movements are no longer available, so these are the alternative replacements. They usually decide to give up the ghost at daylight savings when the time is adjusted.

Hermle units include the following series numbers

  • 2215 (Westminster and Ave Maria pendulum units)
  • 2115 (Westminster and Ave Maria non pendulum units)
  • 2214 (Westminster and Bim Bam pendulum units)
  • 2214 (Westminster and Bim Bam non pendulum units)
  • 2216 (Westminster and Silent Night pendulum units)
  • 2116 (Westminster and Silent Night non pendulum units)
  • 2117 (Ships Bell strike, non pendulum)

Note on the 2117 - There is no quartz unit on the market in today's world that will play ships bell strike unfortunately. It is a tricky situation with these as there is no quartz replacement for this one. You can go with the mechanical if you do not mind spending about $500 and some time / patience with the conversion process, please contact clockworks if you would like to pursue this idea.

- - The content of this web page and web site was written and copyright by James Stoudenmire of Clockworks.com - It may not be used commercially without permission. - -

Hermle Quartz Clock Movement

Hermle 2114 / 2115 Series Discontinued

2114 / 2115 Series (Non Pendulum) Replacement unit 4 1/2W x 2 1/4H x 1 1/8D
Hermle Quartz Clock Movement

Hermle 2214 / 2215 Series Discontinued

2214 / 2215 Series (Pendulum) Replacement unit 4 1/2W x 2 5/8H x 1 1/8D

#MSO Premium Chime

5 1/4" x 4 5/8" x 1 1/8"

Chiming Quartz clock movements
Westminster or Ave Maria, quarterly or on the hour only.
  • Volume control
  • Can be use with or without Pendulum
  • 16" pendulum at longest is used
  • Volume control
View Product
Minimum units Price/unit
1 $64.89
4 $59.89
12 $54.89
Clear
MSO: $64.89

#QU40 Four Melody Chime

4 9/16" x 4 3/4" x 1 1/8"

Chiming Quartz clock movements
Westminster every quarter. Or Westminster, Ave Maria, Bim Bam options only on the hour.
  • Volume control
  • Can be use with or without Pendulum
  • 16" pendulum at longest is used
  • Auto Night Silence Switch
  • Volume control
  • Light Sensor
View Product
Minimum units Price/unit
1 $59.89
5 $54.89
12 $49.89
Clear
QU40P: $59.89

#QU30 Chiming Seiko (Great Sound)

Pendulum unit is 3 1/4"T x 5 1/4"W x 1 5/16"D

Non Pendulum unit is 3 1/4"T x 2 3/8"W x 1 5/16"D

Chiming Quartz clock movements
Westminster or Whittington on the quarters
  • Volume control
  • Pendulum or non pendulum units
  • The smallest chime unit available
  • Auto Night Silence Switch
  • Volume control
View Product
Minimum units Price/unit
1 $49.89
5 $44.89
12 $39.89
Clear
QU30P: $49.89

#QU22 Chiming Takane Quartz

Pendulum unit is 3"T x 4 3/4"W x 1 1/4"D

Non Pendulum unit is 3 1/4"T x 2 3/8"W x 1 5/16"D

Chiming Quartz clock movements
Westminster on the quarters
  • Pendulum or non pendulum units
  • Built in speaker
  • One C cell battery required
  • Wider post alert, its 7/16 wide
View Product
Minimum units Price/unit
1 $39.89
5 $36.89
12 $31.89
Clear
QU22P: $39.89